Maytag Wall Oven Uživatelský manuál stáhnout pdf (Strana 3)

Electrical

Requirements

Warnlng: Improper connection of the

equipment grounding conductor can

result in a risk of electrical shock.

A 120 Volt. 60 Hr. AC only. 15 Ampere

fused electrlcal supply IS reqwed

[tlme-delay fuse or clrcult breaker IS

recommended] It IS recommended that

a separate clrcult sewing only this

appliance be provided DO NOT USE AN

EXTENSION CORD.

A wrung diagram IS Included in Merature

package. The wiring diagram 1s also

located behlnd the control panel

Recommended

Grounding

Method

DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG.

For your personal safety, this appliance

must be grounded This appliance IS

equipped with a power supply cord

haVlnQ 0 3-piO”Q grounding PfUQ To

mln~mlze possible shock hazard. the

cord must be plugged Into a mating 3-

prong Qroundlng type wall receptacle,

grounded I” accordance with the

National Electrical Code. ANSliNFPA

70-1984 ++ and local codes and

ordinances See Figure 1 If a mating wall

ECeDtaCle is not available It IS the

PerSOnal

responslblllty and

obllgationofihe customer

Temporary .

Grounding Method

tiNOr, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG.

r

CPowell”PPlY cora

Electrical ground Is required on this

appliance

If changing and properly grounding

ihe wall receptacle IS impossible and

where local codes permit (consult vour

elecfrical inspecfor]. a tetiporary

adODtOr rnav be oluaaed Into the

existing 2-p&Q ~all~&eptacle to mate

with the &prong power supply cord.

If this is done, you must connect a

separate copper QrOUndlnQ we (No. 18

mInImum) lo a grounded cold water

pipe by means of a clamp and then to

the exiernal grounding connector screw

-

Uo nol

ground

10 a gas supply pipe,

Do not connect to electrical supply

until appliance IS permanently

grounded See Figure 2.

Grounded cold water pipe must

have metal continuity to electrlcai

ground and not be interrupted

by plastic. rubber or other electrical

insulating connectors such as

Now Start...

With wall oven in kitchen.

1

Remove racks and other parts

n

from inside oven

2

Remove shipping materials.

n

tape and protective film from

wall oven. Do Not remove cardboard

ShippIng base at this lime

Remove the

oven control

knob Remove the 2 screws that

attach the control panel to the oven

frame Move the control panel down

and forward Disconnect the plug from

the terminal block. Carefully place

control panel. screws and oven control

knob in a safe location.

If oven WI// be vented outsIde, remove

the flue cover and collar cap See back-

cover for Venting lnstallat~on Instructions.

6

Assemble the flwble connector

n

from the Qas supply pipe in this

order: manual shut-off valve, K” nipple,

%” adaDter. flexlbie connector. W’

adapt& and K” nipple

Flexible connector

Manual

Yz” adapter

YI” adapter

shut-ofl

5

w

Open door to first stop posItIon

and lift door upward and off hInQeS

valve

WARNING: THE REGULATOR IS DIE CAST

IF THE CONNECTION IS MADE TOO

TIGHT, IT WILL CRACK RESULTING IN A

GAS LEAK AND POSSIBLE FIRE OR

EXPLOSION.

7

Lift wall oven up to cabinet

W

cutoul. using the oven opening

as an area to grip. Thread flexible

connector through back of wall oven

Plug the electrical cord Into the

grounded outlet Discard cardboard

shlpping piece

PANEL B

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře